Overview: Deck Builders
A deck is a structure holding people in the air, not an outdoor floor. Under the boards sit footings in undisturbed soil, posts, beams, joists at a spacing matched to their span, and guards and stairs that have to meet code. Most places require a permit, with an inspection of the footings before they are covered and another of the framing before boards go down.
One detail matters more than all the finishes. Where a deck is attached to the house, the ledger board carries the whole load, and decks that collapse almost always tear off at that joint. It has to be bolted through the framing rather than nailed, and flashed so water cannot run behind it and rot the rim board out of sight. Ask any builder how they fasten and flash the ledger. The answer tells you a lot.
After that, choose boards on how you want to spend your weekends: treated lumber is cheapest and needs refinishing, composite costs more and needs washing, hardwood splits the difference and is heavy to work.
Deck companies covering your area are listed by state and city below.
Cost of Building a Deck
Deck size alone is not enough. Match the decking material, height, structure, railings and stairs, and distinguish a new build from resurfacing a sound frame.
| Service or scope | Planning range | What this covers |
|---|---|---|
| New pressure-treated wood deck | $15–$50per square foot of deck area | Build a simple low rectangular deck with pressure-treated framing and decking on an ordinary accessible site; no stair flight or guardrail package is included in this comparison.Confirm the height and whether the local design requires rails or stairs; very small decks may be governed by a minimum project price.Included scope and possible extrasScope used for this estimate: Ordinary footings and framing; Pressure-treated decking and installation Outside this estimate: Guardrails and stair flights; Old-deck removal; Difficult soil or hillside engineering; Permit fees unless listed |
| New composite deck | $40–$75per square foot of deck area | Build a low rectangular deck with a pressure-treated structure and specified composite decking, including ordinary footings and installation.Compare the same composite product tier, fasteners and trim; a premium board alone does not define the whole deck.Included scope and possible extrasScope used for this estimate: Ordinary footings and framing; Specified composite decking and installation Outside this estimate: Guardrails and stair flights; Old-deck demolition; Hillside foundations or structural repairs; Permit fees unless listed |
| Raised composite deck | $50–$100per square foot of deck area | Build an elevated pressure-treated structure with composite decking; the proposal must state height, footing design, guardrail length and the stair allowance.Rail length and stair geometry can change the total independently of deck floor area.Included scope and possible extrasScope used for this estimate: Specified elevated frame, footings and decking; Railing and stair components explicitly included in the package Outside this estimate: Old-deck demolition; Unusual hillside foundation work; Enclosed rooms or roof structures; Permit and design fees unless listed |
| Old deck demolition and removal | $5–$15per square foot of removed deck | Demolish and haul away an accessible ordinary wood deck, measured by the deck floor area.A minimum job charge may apply; ask whether buried concrete footings stay or are removed.Included scope and possible extrasScope used for this estimate: Ordinary deck demolition; Debris haul-away and disposal Outside this estimate: New deck construction; Difficult access; Concrete footing removal unless specifically included |
What changes the price
- Deck height, footing design and site access
- Decking product, railings and stair geometry
- Reusable framing versus demolition and structural repairs
Ask before you book
- Are rails, stairs, footings and demolition in the total?Prevents a surface-only number being mistaken for a complete deck.
- What must be checked before the existing frame can be reused?Clarifies the risk in a low resurfacing estimate.
- Which product line and fastening system are specified?Makes material quality and installation method comparable.
Check the scope
A deck-board price excludes the structure. Compare a complete drawing with height, footings, railing length and stairs, and ask whether the existing frame is suitable for reuse.
Compare quotes wisely
Ask for a simpler rectangular layout and separately priced material options before changing required structural details.
How to read these estimates
These ranges combine published U.S. prices and cost guidance for the stated work. They are budgeting estimates, not offers from listed companies or a statistical national average. Confirm the total, included work and additional charges in writing.
U.S. planning estimates. Local quotes vary by location and the scope of work.
Frequently asked questions
What holds a deck onto the house?
A ledger board bolted through the house framing, with flashing over the top so water cannot get behind it. Nails and deck screws are not enough, and this is the connection that fails when a deck comes down with people on it. A free-standing deck carried on its own posts avoids the joint entirely and is worth asking about.
Does a deck need a permit?
Usually, once it is attached to the house or raised above a low height, and the rules come from the city or county. Expect an inspection of the footings before they are backfilled and another of the framing before the boards cover it. Building without one causes real trouble at resale, when a buyer's inspector finds a structure with no record.
How deep should deck footings go?
Below the frost line for your area and down to soil that has not been disturbed, with the base wide enough to spread the load the post carries. Precast blocks sitting on the ground are fine for a low platform and nothing else. On fill or soft ground, helical piles or a deeper pier are the usual solutions.
Treated lumber, composite or hardwood?
Treated pine is cheapest and wants cleaning and refinishing on a cycle. Composite costs more up front, never needs a stain, and gets hot underfoot in full sun. Hardwoods look better than either and are hard on tools and on the person installing them. Whatever the boards are, the frame under them is still lumber and still needs the detailing done right.
What do railings and stairs have to meet?
Codes set guard height, how much sideways force a guard must take, and the gap between balusters, which is sized so a small child cannot pass through. Stairs need consistent rise and run, a graspable handrail, and a solid landing at the bottom rather than a paving slab dropped on grass. This is the part of a deck an inspector checks hardest.
How much upkeep does a deck need?
Once a year, clear the gaps between boards so they drain, wash the surface, and look at the structure while you are down there: the ledger and its flashing, rusted fasteners, posts where they meet the ground, and any guard that moves when pushed. Refinish wood when water stops beading on it. Composite gets washed and nothing else.